| “This site contains affiliate links for which OEMDTC may be compensated” |
2014-2016 MAZDA6 – TPMS WARNING LIGHT ON
APPLICABLE MODEL(S)/VINS
2014-2015 Mazda6 vehicles (except Canada and Mexico) with VINs between JM1 GJ1 ****** 224859-225009 (produced between November 27, 2014 – December 01, 2014)
2016 Mazda6 vehicles with VINs between JM1 GJ1 ****** 400011-412885 (produced between November 24, 2014 – February 11, 2015)
Except Canada and Mexico
Tire Pressure Monitoring System (TPMS) warning light on even if the TPMS system has been properly initialized at the specified tire air pressure.
This may be caused by improper tire air pressure detection by the TPMS system on certain types of road surfaces.
Canada and Mexico
Tire Pressure Monitoring System (TPMS) warning light on even if the TPMS system has been properly initialized at the specified tire air pressure.
REPAIR PROCEDURE
- Verify that the recall campaign 8014J is closed or not applicable for the vehicle (Except Canada and Mexico).
- Reboot the IDS to clear memory before reprogramming.
- Using IDS 94.02 or later software, reprogram the ABS module to the latest calibration following the “Module Reprogramming” procedure.
NOTE: ABS module reprogramming may fail if VCM cable connections are poor and/or battery voltage is low. For details, refer to “SERVICE CAUTION FOR ABS MODULE REPROGRAMMING”
- Select “Module Reprogramming”, then select “ABS”.
- The following screen will be displayed:
Click “YES” and follow the M-MDS instructions to reprogram the ABS module.
If the message “No later calibration is available on the system for this ABS” is displayed, the ABS module is already at the latest calibration. “Current level in Vehicle” will show the new file name. This service bulletin does not apply.
NOTE: If reprogramming stops before completion, refer to “SERVICE CAUTION FOR ABS MODULE REPROGRAMMING”
- After reprogramming, remove the session. Then, open a new session again and go to the “Log Viewer” screen on which the programmed file name is displayed as shown in figure below. If the new file name matches the list, the reprogramming has been successfully completed.
NOTE:
- After reprogramming, communication error related DTCs may be stored. This is a normal operation. Delete these DTCs.
| Possible DTCs: | |
| U0155:00-28 | EATC – Communication error with instrument cluster |
| U2300:54-28 | EATC – Configuration error (data not received) |
| U0155:00-08 | R_BCM – Communication error with instrument cluster |
| U0100:00-28 | BSML – Communication error with PCM |
| U0155:00-28 | BSML – Communication error with instrument cluster |
| U0214:00-28 | BSML – Communication error with start stop unit |
| U0100:00-28 | BSMR – Communication error with PCM |
| U0155:00-28 | BSMR – Communication error with instrument cluster |
| U0214:00-28 | BSMR – Communication error with start stop unit |
| U0316:09-08 | SBS/MRCC – Error signal received from DSC HU/CM |
| C0023:62-08 | ABS – Brake light/Brake switch |
- In some cases, the ABS warning light may illuminate and the engine will not shut off by one-press of the engine start/stop button. To correct this concern, disconnect the ABS/DSC 30A fuse for 10 seconds.
IMPORTANT INFORMATION FOR MODULE PROGRAMMING
- Always update the IDS tool first, then follow on-screen instructions to download the needed calibration file for ABS module reprogramming.
- It is not necessary to remove any fuses or relays during ABS module reprogramming when the IDS screen prompts you to do so. You may accidentally stop power to one of the ABS module terminals and cause the ABS module to be blanked, or you may receive error messages during the IDS reprogramming procedure.
- IDS shows the calibration part numbers after programming the ABS module.
- Please be aware that ABS module calibration part numbers and file names listed in any Service Bulletin may change due to future releases of IDS software, and additional revisions made to those calibrations for service related concerns.
- When reprogramming an ABS module, IDS will always display the “latest” calibration P/N available for that vehicle. If any calibration has been revised/updated to contain new information for a new service concern/issue, it will also contain all previously released calibrations.
SERVICE CAUTION FOR ABS MODULE REPROGRAMMING
NOTE: Poor connection between the vehicle and M-MDS and/or low voltage may result in abnormal termination and/or ABS data corruption.
- Make sure the following connections are secured. Do NOT touch the VCM and DLC cable. This may cause electrical noise and connection disruption.
– Between the vehicle-side connector and the DLC cable.
– Between the PC-side connector and USB port of PC.
- Connect AC adapter to the PC in order to stabilize voltage fluctuation during reprogramming.
Do NOT use vehicle battery outlet as power source for the PC.
- When performing this procedure, we recommend using the “Power Supply” mode in the Battery Management System to keep the vehicle battery up to capacity. If a different charger is used, make sure it does not exceed 20 AMPS. If it exceeds 20 AMPS, it could damage the VCM.
Before reprogramming, pay attention to the vehicle condition and PC environment.
- Turn off all the electrical loads, especially the A/C (blower), audio, rear defogger and headlights.
- Perform self-test and verify no DTC is stored. If any DTC is stored, fix the concern and delete the DTC.
- Disconnect all non-genuine aftermarket accessories.
- Terminate all programs other than IDS on the PC. This may extend reprogramming, PC may freeze or it may cause other problems.
- Verify that the latest IDS software is installed on the PC.
- Perform reprogramming under proper Internet environment. Especially when using wireless network, make sure the connection is strong.
- Make sure to keep proper free space on the PC’s hard disc. Insufficient free space (less than 1 GB) may result in PC freeze during reprogramming.
Trouble Shooting Procedure for ABS Module Reprogramming
Before performing the following trouble shooting procedure, check all VCM cable connections and the battery voltage.
Failure screen
- If the screen shows “The programming failed. Do you wish to retry?” with Yes/No buttons, DO NOT Click the buttons and proceed to “Recovery” below.
- If the screen shows “The programming failed.” without Yes/No buttons, the ABS module has to be replaced with new one.
Recovery
- Turn IG off. (If needed, press and hold the start button.)
- Remove the ABS/DSC 30A fuse for 10 seconds.
- Install the fuse and turn IG ON.
- Click “Yes” button and follow the on-screen instruction.
- Click the check button.
- Click the “Confirm” button.
- Turn IG OFF.
- Click the check button.
- Turn IG ON. Reprogramming will resume.
- After performing the ABS module reprogramming procedure, adjust all four tire pressures to the specification and initialize the TPMS using IDS.
NOTE:
- ABS module reprogramming does not reset TPMS misuse prevention history.
- DO NOT press the TPMS set switch after ABS module programming. This may cause the vehicle to enter the TPMS misuse prevention mode.
Select the following items from the initial screen of the IDS or Scan Tool.
- Verify the repair by starting the engine and making sure there are no MIL illumination or abnormal warning lights present.
NOTE: After ABS module reprogramming, it is no longer necessary to road test the vehicle to “relearn” KAM (Keep Alive Memory).
CALIBRATION/PART(S) INFORMATION
| File Name | Note 1 | Note 2 | Equivalent ABS modulepart number |
| GHR1-437AS-3-90 | With MRCC* | Without EPB** | GHY1-437A0-H |
| GHP9-437AS-3-90 | Without MRCC* | GHY9-437A0-H | |
| GMM1-437AS-0-70 | With MRCC* | With EPB** | GMY1-437A0-C |
| GMM4-437AS-0-70 | Without MRCC* | GMY4-437A0-C |
* Mazda Radar Cruise Control (MRCC)
** Electric Parking Brake (EPB)
Mazda Reprogramming
Mazda Reprogramming
MDSFA/MMP Required Hardware (Not Included)
As shown in the diagram, an SAE J2534 pass-thru device is required to use the application.
Hardware validated by Mazda can be purchased separately from a third-party supplier. Validation has been done using the following J2534 pass-thru device and cables:
- CarDAQ+ (includes RS232 and Ethernet cables)
- Cable between CarDAQ and Vehicle – CD2534-J1962-FEPS (Sold separately / Required)
Important Information: Mazda makes no representations about the performance of third-party passthru devices. This pass-thru device list is provided voluntarily and as a courtesy. While our software meets SAE J2534, the pass-thru device manufacturer is responsible for making sure their pass-thru device operates properly on each Mazda vehicle and with Mazda software. We have listed the devices below because their manufacturers have attested that the tools have been validated to work. From time to time, we may test these devices. If we determine they do not operate properly or are obsolete, we may remove them from the list, without notice. Additionally, pass-thru devices listed here have been listed for their use with Mazda North American products only. While they may work with some European and other vehicles, they may not meet the requirements for those regions or operate properly.
Hardware can be purchased from a third-party supplier. Mazda has validated the following J2534 passthru devices:
| **J2534 Pass-thru Device | Manufacturer |
| *CarDAQ+ | Drew Technologies Inc. |
| *Pass-Thru+XS | Actia Corp. |
| *Snap-On Pass Thru Pro II | Snap-On. |
| *Universal Reprogrammer | EASE Diagnostics |
| *FLASH2 All-Makes Reprogrammer | CARDONE Industries |
| *Bosch Mastertech VCI | Bosch Diagnostics |
*Contact the device manufacturer for the latest DLL and firmware versions.
**Many J2534 manufacturers sell and market similar J2534 devices with like names. Please exercise caution when using the list above for purposes of understanding devices Mazda has validated for use. J2534 Pass-thru Device Suppliers: Mazda has validated the J2534 devices listed on this page. Mazda does not plan to validate additional J2534 devices at this time.
PCM Reprogramming Process Overview
- Purchase a subscription to PCM Reprogramming on this website.
- Download the application and install it on your PC.
- Connect the J2534 pass-thru device to the PC and the vehicle, and power it up.
- Run the application installed on your PC.
- The application will determine whether or not a new calibration file is available.
- If you choose to use the new file, the module will be reprogrammed.
- If PATS functionality is required, it can be chosen from the toolbox.
https://www.mazdaserviceinfo.com/pcm-reflashing
- ALL OF THE J2534 PROTOCOLS - This single unit has all of the protocols you need for your OEM J2534 reprogramming and diagnostics including the latest in DoIP and CanFD
- J2534 TECHNICAL SUPPORT - FREE for the life of the tool. Staffed by technicians who understand vehicle repair and J2534 Pass‑thru
- TOOLBOX WITH OEM APPLICATION DESCRIPTIONS - educational video tutorials and real-time news – Giving you the confidence and up-to-date knowledge to get the job done
- J2534 v05.00 API - The newest version of J2534 to give you the latest in pass-thru technology
- FUTURE PROOF WITH 4 CAN CHANNELS - Going beyond the 3 required by select Chrysler/FCA models, CarDAQ-Plus 3 also provides a 4th to meet the needs of future OEM applications
- 🆚LAUNCH X431 PRO5 scan tool Upgrade all functions of X431 PRO3/X-431 Throttle III/X431-TorqueIII/X431 V+, PROS V+, PAD3. ⓵ J2534 ECU Programming &Online functions directly connect to OEM server, 50+ reset same as X-431 Throttle;⓶Bi-directional control and All system diagnostics as Snap-on scanner; ⓷ Support 150+ brands Vehicles (include CAN/CAFD/DoIP/HD protocols and AutoAuth for FCA SGW) ⓸Powered by 8-core processor(1.8GHz), Android9.0 OS, 2.4 & 5GHz WiFi connection.
- 🚜[J2534 Reprogramming With FREE SMARTBOX 3.0】Save more than $2000, LAUNCH X431 PRO5 support J2534/DOIP/CANFD/HD protocols (Needn’t buy HDIII Module,Manufacture software and non-16pin adaptors need to be purchased separately.) Download OEM software from the manufacturer’s server to 1) program data to blank/used ECUs; 2) Reflash ECUs with data loss; 3)Upgrade ECU software version. As a wireless VCI allowing the vehicle to transmit data to the diagnostic tablet without a physical connection.
- 👏[50+ Reset, Continuously Updated Reset Functions]: With the LAUNCH diagnostic tool, You will never be bothered by tricky vehicle issues and keep pace with newer technology. 50 commonly reset functions ( in the quick page ) reaching into the smallest parts to root out the problems. Extra 300+ repair functions ( in-vehicle catalog) for specific models extend the capability to reset, regeneration, initiation, matching, etc. (Functions vary by models, configurations, and systems.)
- 🌐[One stop Intelligent Diagnostic Tool]: LAUNCH X431 PRO5 obd2 scanner Bluetooth provides Repair Tips, Repair Assist, Component Measurement, TSB, Relevant Cases DTC Analysis to simplify complex diagnostic and achieve the trouble-free repair. 🤩[One Scanner For Multiple Uses]: LAUNCH diagnostic tool PRO5 collaborates with add-on modules (ADAS, Videoscope, TSGUN, X-ProG3, WiFi Pinter, Battery Tester) to expand business applications and improve diagnostic accuracy.
- 👍【2024 New OE Level Online Functions 】Bidirectional Scan Tool offers you various high-end online functions, which enable you to access the online data to do fast & complicated vehicle repairs, e.g. 1) ECU Coding for replacing, match, relearn, recode new ECU modules; 2) Online Coding for BMW, Audi, VW, Porsche, Benz to surf OEM data; 3) VAG Guided functions ease complex issues; 4) Personalization & ADAS improving car performance and driving safety.
- 🌐【Works with Autel MK908, MS908(S/Pro), MK908P, MaxiSys Elite】Autel J2534 work with these tools to program ECUs on specific BMW/ BENZ for specific functions. ★★NOTE: J2534 CANNOT directly work with these single devices. After you received the J2534, you HAVE TO send us both the S/N(12 digits) of your scanner MS908S(etc.) and J2534. So, technically, Autel engineers can help you bind J2534 with your devices. If need any supports, contact us via: 🚘auteldirect @ outlook. com🚘.
- 🌐【SAE J2534-1 & J2534-2 Standards】Autel MaxiFlash Elite J2534 is a fully compliant SAE J2534-1 & SAE J2534-2 (March 2006) device, which performs standard PassThru J2534 functionality: Compatible with for Toyota Techstream, Volvo VIDA, Honda HDS, Jaguar-Land Rover IDS and BMW 3G for OEM diagnostics. Autel MaxiFlash J2534 is also specially designed to provide users with P-C communication and ECU reprogramming capabilities on any modern vehicle diagnostic bus, reliability and flexibility.
- 🌐【High-speed Transmission Speed】Autel MaxiFlash Elite Reprogramming Device J2534 supports simultaneous communication definition in J2534-1, running 3 protocols at the same time, which greatly improves reprogramming and diagnostic speed. Embedded with the ARM9 Dual-core processor (clocked up to 500MHz), which further boosts the communicating speed to save more times and win more business.
- 🌐【Multiple Devices Connected with PC】Autel MaxiFlash Elite J2534 also supports multiple device connections to the PC, which can operate diagnostic and reprogramming functions on more than one vehicle at the same time. Autel MaxiFlash Elite J2534 built-in wireless and data storage, which can update via Internet. It also ensures quickly reprogramming even the newest controllers.
- 🌐【Extensive Compatibility】Autel MaxiFlash J2534 is compatible with Toyota Techstream, Volvo VIDA, Honda HDS, Jaguar-Land Rover IDS and BMW 3G for OEM diagnostics. To check compatibility, please contact 🚘auteldirect @ outlook . com🚘 directly for satisfaction-guaranteed support!
- Application:Support most all of J2534 compatible software, most all of for software, ECU reprogramming in J2534 mode with programming voltage, supply software for diagnosing J1979 compatible vehicles.
- Material:VNCI (Vehicle network communication interface) is a device that works between diagnostic software and vehicle. It is compatible with J2534 Passthru and for .
- Advantage:Support J2534 and for mode in one device, and has automatic switch mode, more speedup, faster communication and reprogramming.VNCI J2534 for Nano protocol configuration include, for ISO15765, for ISO9141, for ISO14230, for J1850 PWM( supports IFR and 2X speed modes), for J1850 VPW (supports 4x speed mode).
- Easy to install:More stability, never let you down while reprogramming, portable and convenient, small package and easy to carry.
- Best Experience :We strive to provide you with the best quality products and the best customer experience.We try our best to meet your requirements.Please check the product information carefuly berore buying to aviod making mistakes.
- Industry-leading J2534 Pass-Thru Technology: Enabling diagnostics, reprogramming and security functions for dealerships and the independent repair facility. Economical and compact pass-thru devices provides an easy-to-use interface that allows you to repair complex vehicles with OE applications in your shop. Each type (see single branded types above) Mongoose-Plus is engineered to work with one of the following OEM's J2534 applications for Chrysler, Ford, GM, Nissan, Toyota, Subaru, & VW/Audi.
- Supports Current GM Vehicles: Now includes CAN-FD, DoIP (Diagnostics over Internet Protocol - as defined in J2534-2) and support for J2534 version 5.0. This is the tool that GM dealerships use for diagnostics and reprogramming.
- NEW Bluetooth Wireless Options Available: Providing wireless connectivity between your laptop and the Mongoose-Plus
- Expert Product Support: Staffed by technicians who understand vehicle repair and J2534 Pass‑Thru applications to help you with any technical setup questions
- Key Registration and Immobilizer Support: Using NASTF Vehicle Security Professional credentials
- Stay up-to-date with thelatest firmware and support of the SM2Pro J2534VCI ECUs programmer, ensuring reliable perform and optimalresults.
- The SM2Pro J2534VCI ECUs programmer is a trustedtool for professional technicians, offering comprehensive functionality and easy integration into your workflows.
- The SM2Pro J2534VCI ECUs programmer offersadvanced functionality for efficient and precise ECUs programming.
- With its 67IN1 without dongle & OBDcompatibility, the SM2Pro J2534VCI ECUs programmer provides a versatilesolution for read and write operations.
- Experienceseamless ECUs programming with the SM2Pro J2534VCI, designed to streamlines the read and write processes for enhanced efficiency.
Last update on 2024-03-19 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.