“This site contains affiliate links for which OEMDTC may be compensated” |
NHTSA ID Number: 10093141
Manufacturer Communication Number: 05-004-16-3188
Summary
WHEN PRESSING THE START/STOP BUTTON, THE IGNITION MAY NOT TURN OFF ON SOME VEHICLES EQUIPPED WITH A GATE-TYPE AT SHIFTER. ALTHOUGH THE SHIFT LEVER IS IN “P” POSITION AND THE ENGINE SHUTS OFF NORMALLY, THE IGNITION MAY STAY ON (IN ACCESSORY MODE).THIS CONCERN MAY BE CAUSED BY A WORN SWITCH UNIT. TO ELIMINATE THIS CONCERN, THE SWITCH UNIT MATERIAL HAS BEEN CHANGED TO IMPROVE WEAR RESISTANCE. MODIFIED SWITCH UNITS HAVE BEEN ESTABLISHED AS NEW SERVICE PARTS.
3 Affected Products
Vehicles
MAKE | MODEL | YEAR |
MAZDA | CX-5 | 2013-2014 |
MAZDA | MAZDA6 | 2014 |
APPLICABLE MODEL(S)/VINS
2013-2014 CX-5 vehicles with VINs lower than JM3KE******430747 (produced before Dec. 27, 2013)
2014 Mazda6 vehicles with VINs lower than JM1GJ******162747 (produced before Nov. 29, 2013)
DESCRIPTION
When pressing the START/STOP button, the ignition may not turn off on some vehicles equipped with a gate-type AT shifter. Although the shift lever is in “P” position and the engine shuts off normally, the ignition may stay on (in accessory mode).
This concern may be caused by a worn switch unit.
To eliminate this concern, the switch unit material has been changed to improve wear resistance. Modified switch units have been established as new service parts.
REPAIR PROCEDURE
- Remove Mazda6 front console box (A) or CX-5 rear console (A) according to the instructions on MS3 online or the Workshop Manual to access the switch unit (B):
- MAZDA6 FRONT CONSOLE BOX: (section 09-17).
- CX-5 REAR CONSOLE: (section 09-17).
- Detach (4) four hooks (A) (2 hooks shown below), then remove the set plate assembly (B).
NOTE: In these illustrations, the shift lever component is shown removed from the vehicle for viewing purposes only. It is not necessary to remove it from the vehicle during this repair.
- Detaching (2) two hooks (A) pull out the shift lock over-ride lever (B).
- Remove (2) two screws (A). While pushing the stopper (B) down, remove the switch unit (C).
- Disconnect the switch unit connector (D).
- Install a new switch unit in the reverse order of removal.
NOTE: Use the new screws that came with the new switch unit.
- Tighten the screws to the correct torque specification.
Tightening Torque: 10.6-14.2 in. lbf. {1.2-1.6 N-m, 12.2-16.3 kgf-cm}
CAUTION: Over tightening the screws may cause breakage of the plastic parts.
- Re-install other parts in the reverse order of removal.
PART(S) INFORMATION
Part Number | Description | Qty. | Applicable Select Lever Assembly |
KDY0-46-040 | Switch Unit | 1 | KD31-46-100D |
GHR5-46-100C |
NOTE: The Applicable Select Lever Assembly part numbers listed above are for reference only. Do not order these parts for this repair. It is only necessary to order the Switch Unit.
05-004/16
04/11/2016
https://www.nhtsa.gov/recalls?nhtsaId=10093141
https://static.nhtsa.gov/odi/tsbs/2016/SB-10093141-6903.pdf
NHTSA ID Number: 10105637
Manufacturer Communication Number: 05-007-15-3115
- SLEEK & DURABLE TRIM TOOL SET - Our premium grade auto trim removal tool set fits in any crevices and works excellent in removing exterior & interior trim, molding, wheel hubs, door panel removal tool, plastic pry tool, fasteners, dashboards, and more without scratching or damaging your car.
- UNIVERSAL AUTO TRIM REMOVAL TOOL KIT - It includes 5 job-specific auto trim removal tools to make internal and external automotive removals easy. It is designed with care to be universally applicable to vehicles, boats, RVs, and more so you can make repairs and maintenance with ease while also protecting the aesthetic of your car with its sleek design.
- UNIQUE ERGONOMIC DESIGN - This is made of sturdy and pliable nylon material with a unique ergonomic design that enables the tools to be easily handled to effectively save effort and time while working on laborious repair or maintenance tasks.
- EASY & CONVENIENT - Perfect for professionals and beginners doing any care modifications. It's also compact in size which makes it easy and convenient to carry or stash in your car so you can use it anytime, anywhere.
- Premium Grade Nylon: Made of impacted resistant nylon fiber material with high level craftsmanship, it’s non-toxic, durable and not like brittle material which is prone to bent or crack
- Multi-function tools:These 5 PCS different kinds of trim tools used for car audio/radio system installing or removing, dash panel, moldings, emblems, window trims or automotive interior repairing and furniture restoration
- Good Helper: Whenever you need them, they are always here to help you. It would be an excellent choice to work with this kit
- Ergonomic Design: GOOACC trim removal tool kit is made in accordance with ergonomics design with super lightweight and easy handheld features which effectively effort saving for various interior and exterior car trimming
- Package Include:Including 4 pcs car dash panel removal tool and 1 fastener remover, total 5 pcs auto trim removal tool
- 5 Pack Trim Tools Kit : There are 5 pcs different kinds of trim tools, including 4 pcs car door panel removal tool and 1 pcs fastener remover .
- Multifunctional Use : These Car Trim Remoaval Tools work great for car audio/radio system installing or removing, door panel, moldings, emblems, window trims or automotive interior repairing and furniture restoration
- Trim Removal Tools :Auto interior trim removal tool is easy to hold in hand and access to some hard-to-reach spaces and crevices. It is a great car repair tool for professionals and beginners doing any car modifications.
- PRY TOOL SET : This pry tool set made of super durable plastic material for long-time usage. Ergonomic design with super lightweight, easy handheld features which effectively effort saving for various interior and exterior car trimming in the shortest time.
- Total 13 Pack : You will get 5 Pcs Trim Tools and 8 Pcs Tire Caps Valve;Easy to install or remove the car accessories without breaking. The sharp and clean edge of the trim tool ensures the good effect of using and curved and ultra thin clip head can reach the confined areas without pry off the trim.
- 12 Most Popular Sizes : There are 12 most common sizes of clips which will meet your needs, sturdy and reusable, compatible for GM, Chrysler, Ford, Toyota, Nissan, Mazda. Hyundai, Kia, AMC, Jeep, etc…
- Multifunctional: Different kinds of door panel removal tools are available for you, excellent for Automotive, Marine, Furniture or Aircraft Trim removal and installation, including Door Panels, Moldings, Window Trims, Clips, Fasteners, Emblems, Panels, Radios, etc...
- Upgraded Material: Made of impacted resistant nylon fiber material with high-level craftsmanship, it’s non-toxic and durable, would be an excellent choice for you
- Easy Storage: Come with a portable bag helps you carry all kits and is less prone to loosing, would greatly save your time and space
- Package Include: 238Pcs Trim Removal Tool
- Easily remove and replace plastic push pins found on various vehicle's trims and body components
- Helps to remove pins without damage, ensuring they could be used again
- Craftsman Comfort Grip Design
- AUTO-TRIM REMOVAL KIT: Our auto tool kit makes removing clips and fasteners easy, safe, and quick. The shafts have pivot points for appropriate leverage to help prevent twisting that can scratch a door panel or trim piece.
- DURABLE CAR TOOLS: This automotive tool kit includes 5 high-quality tools. The shafts are designed with SVCM satin chrome-plated steel for ultimate durability so they can last through many vehicle repair projects for years to come.
- VERSATILE TRIM-PANEL SET: Perfect for use on most vehicles, our automotive tools help remove clips and fasteners that secure upholstery, panels, and more. The shafts are also suitable for interior work, including on a dashboard, stereo, or radio.
- COMFORTABLE GRIP: Each shaft is equipped with an ergonomically shaped handle with a soft-grip coating to keep your hands comfortable during long projects. These ultra-comfortable accessories make the perfect addition to any car tool kit.
- THE RIGHT SIZE This 5-piece auto-body tool set includes different sizes to fit your fastening needs. It includes 1 square-notch tip, 1 large “V”-notch tip, 1 small “V”-notch tip, one 1/4-inch “U”-notch tip, and one 5/16-inch “U”-notch tip.
- 【MULTI-PURPOSE USAGE】- The GOOACC car trimming removal toolset consists of 40pcs different tools,excellent for Automotive, Marine, Furniture or Aircraft Trim removal and installation, including Car Panels, Moldings, Window Trims, Clips, Fasteners, Emblems, Panels, Radios, ect.
- 【PROTECT YOUR CAR】- Our car tools is made of impact resistant nylon material,it will not scratch or damage to car paint in the whole modification process.
- 【TIME AND LABOR-SAVING】-This auto tool kit adopts ergonomic design with super lightweight and easy handheld features which effectively effort saving for various interior and exterior car trimming.
- 【EASY FOR STORAGE】- Come with portable zipper store pouch to Store All Of Your Tools After Use. You won't worry about to lose them
- 【PACKAGE INCLUDE】-11PCS Trim Removal Tools, 1PCS Trim Clip Removal Pliers, 1PCS Car Foil Small Scraper Tool, 2PCS upholstery fastener remover, 4 PCS precision hook pick, 8 PCS stainless steel stereo removal tools, 11PCS stainless steel Auto Terminal Removal Key Tool, 1PCS wiring threader, 1PCS tightening device and a portable storage bag
- Multi-function tools: There are 19 pcs different kinds of panel removal tools, excellent for Automotive, Marine, Furniture or Aircraft Trim removal and installation, including Panels, Moldings, Window Trims, Clips, Fasteners, Emblems, Panels, Radios, etc...
- Premium Grade Nylon: Made of impacted resistant nylon fiber material with high level craftsmanship, it’s non-toxic and have long last, not like brittle material which is easy to bent or crack
- Good helper: Whenever you need them, they are always here to help you. It will be an excellent choice for you to work on your car with this set
- No damaging: These tools helps you work on your car easily without damaging it. It won’t scratch or damage your car like some poor quality tools
- Package Include:Including 11pcs interior trim disassemble tools, 2pcs release tools, 2pcs stereo removal tools, 3pcs Car terminal removal tools, 1pc Trim Clip Removal Pliers, and a portable storage bag
- MADE BY FIRM AND DURABLE FIBER MATERIAS: The decent upholstery fastener and romoval tools constructed from durable hard plastic can facilitate removing door panels, trim, grills without scratch.
- INSTALL, REMOVE, REPAIR, FASTEN OR RESTORE WITH MULTIFUNCTION: Good value for doing DIY disassembly and repair on car trim, wheel well covers, bumpers, car audio system, dashboard, vent and other components.
- TO BE USED WITH EASE & WITHOUT ANY SCRATCH: Hardly break or bend with durable thick plastic, make scratching the paint or scarring on delicate auto part like metal ones almost non-existent.
- 5PCS TRIM MOLDING REMOVAL PACKAGE: Includes 4 different specifcations of auto panel removal kit + 1 piece of fastener remover in lightweight and convenient panel protecting solution.
- TRIM TOOLS FOR MULTIPLE USAGES: Trim removal tool Kits work great for automotive, marine, furniture or even aircraft trim removal and installation.
- Made of super durable plastic material for long-time usage. Ergonomic design with super lightweight, easy handheld features which effectively effort saving for various interior and exterior car trimming in the shortest time.
- Great for car audio/radio system installing or removing, door panel, moldings, window trims or automotive interior repairing and furniture restoration.
- Package includes 4 plastic panel removal tool + 1 fastener remover to facilitate your needs when repairing. A professional tool kit that is sturdy and easy to use.
- Made of impact resistant nylon fiber material with matte surface treatment, tougher than common ABS one, it is eco-friendly, non-toxic and breakage-proof.
- All tools are molded according to car trimming needs on the market, moderate curve that is not sharp, anti-scratches and harmless to car paint in the whole modification [Universal Application] This multi-functional combination tool set designed for all models of cars, boats, and rvs trimming jobs with variety of shapes and sizes, even for hard to reach areas.
Last update on 2024-04-18 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
SEOCONTENT-START
Page 1 of 4
CONSUMER NOTICE: The information and instructions in this bulletin are intended for use by skilled technicians. Mazda technicians utilize the proper tools/
equipment and take training to correctly and safely maintain Mazda vehicles. These instructions should not be performed by “do-it-yourselfers.” Customers
should not assume this bulletin applies to their vehicle or that their vehicle will develop the described concern. To determine if the information applies,
customers should contact their nearest authorized Mazda dealership. Mazda North American Operations reserves the right to alter the specifications and
contents of this bulletin without obligation or advance notice. All rights reserved. No part of this bulletin may be reproduced in any form or by any means,
electronic or mechanical—including photocopying and recording and the use of any kind of information storage and retrieval system —without permission in
writing.
© 2016 Mazda Motor of America, Inc.
Subject:
IGNITION DOES NOT TURN OFF WHEN PRESSING START / STOP BUTTON
Bulletin No: 05-004/16
Last Issued: 04/11/2016
Service Bulletin Mazda North American Operations
Irvine, CA 92618-2922
MULTI-MODEL – IGNITION DOES NOT TURN OFF WHEN PRESSING START / STOP BUTTON
BULLETIN NOTE
This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red beside the
change bars.
APPLICABLE MODEL(S)/VINS
2013-2014 CX-5 vehicles with VINs lower than JM3KE******430747 (produced before Dec. 27, 2013)
2014 Mazda6 vehicles with VINs lower than JM1GJ******162747 (produced before Nov. 29, 2013)
DESCRIPTION
When pressing the START/STOP button, the ignition may not turn off on some vehicles equipped with a gatetype
AT shifter. Although the shift lever is in “P” position and the engine shuts off normally, the ignition may stay
on (in accessory mode).
This concern may be caused by a worn switch unit. To eliminate this concern, the switch unit material has been
changed to improve wear resistance. Modified switch units have been established as new service parts.
Customers having this concern should have their vehicle repaired using the following repair procedure.
Previous TSBs: Date(s) Issued:
05-007/15 12/22/15
Bulletin No: 05-004/16
© 2016 Mazda Motor of America, Inc.
Last Issued: 04/11/2016
Page 2 of 4
REPAIR PROCEDURE
1. Verify the customer concern.
2. Remove Mazda6 front console box (A) or CX-5 rear console (A) according to the instructions on MS3 online
or the Workshop Manual to access the switch unit (B):
• MAZDA6 FRONT CONSOLE BOX: (section 09-17 FRONT CONSOLE BOX REMOVAL/INSTALLATION).
• CX-5 REAR CONSOLE: (section 09-17 REAR CONSOLE REMOVAL/INSTALLATION).
Bulletin No: 05-004/16
© 2016 Mazda Motor of America, Inc.
Last Issued: 04/11/2016
Page 3 of 4
3. Detach (4) four hooks (A) (2 hooks shown below), then remove the set plate assembly (B).
NOTE: In these illustrations, the shift lever component is shown removed from the vehicle for viewing purposes
only. It is not necessary to remove it from the vehicle during this repair.
4. Detaching (2) two hooks (A) pull out the shift lock over-ride lever (B).
5. Remove (2) two screws (A). While pushing the stopper (B) down, remove the switch unit (C).
6. Disconnect the switch unit connector (D).
Bulletin No: 05-004/16
© 2016 Mazda Motor of America, Inc.
Last Issued: 04/11/2016
Page 4 of 4
7. Install a new switch unit in the reverse order of removal.
NOTE: Use the new screws that came with the new switch unit.
8. Tighten the screws to the correct torque specification.
Tightening Torque: 10.6-14.2 in. lbf. {1.2-1.6 N-m, 12.2-16.3 kgf-cm}
CAUTION: Over tightening the screws may cause breakage of the plastic parts.
9. Re-install other parts in the reverse order of removal.
10. Verify the repair.
PART(S) INFORMATION
NOTE: The Applicable Select Lever Assembly part numbers listed above are for reference only. Do not order
these parts for this repair. It is only necessary to order the Switch Unit.
WARRANTY INFORMATION
NOTE:
• This warranty information applies only to verified customer complaints on vehicles eligible for warranty
repair.
• This repair will be covered under Mazda’s New Vehicle Limited Warranty term.
• Additional diagnostic time cannot be claimed for this repair.
Part Number Description Qty. Applicable Select Lever Assembly
KDY0-46-040 Switch Unit 1 KD31-46-100D
GHR5-46-100C
CX-5 Mazda6
Warranty Type A A
Symptom Code 62 62
Damage Code 9C 9C
Part Number Main Cause KDY0-46-040 KDY0-46-040
Quantity 1 1
Operation Number / Labor Hours: XXL96BRX / 0.3 Hrs. XXL96ARX / 0.4 Hrs.
SEOCONTENT-END
Mazda won’t turn off radio fix
https://youtu.be/JKPLChc6vMM
or
Mazda CX-5 wont shut off FIXED(2014)
https://youtu.be/Vyq-Pp-iG6U
part need : AT Shift Switch KDY0-46-040 about $45 ~ $65
Hi everyone,
I just made this repair but now my car won’t start. The auxillary stuff comes on but the engine wont turn over. Any ideas? Thanks.
Something not plugged in, or a bad switch maybe.
Hello, I just did the repair and the same thing is happening to me. Did you figure out what was wrong or causing it? Thank you
I just completed this replacement & did it with just a snub Phillips screwdriver (to remove the actual switch) and a regular flat head screwdriver to remove the panels. Works great now and the part was $75 at my local dealer. The exchange is easier if you remove the center cup holder on the Mazda 6. Not sure about other models. Good luck!
Did you have to remove the front console panels as shown, or just the center console?
Is this a safety concern? Should it be a recall?
YES! Ours died. Towed to dealer. Supposedly repaired. Took 4 tries to exit the dealership. They told us the part is sticky at first. Drove 30 miles home. Went into neutral crossing Rt 1 with no light. Death waiting to happen. Towed back to dealer. We’ll see
Hello
where exactly is this located? I want to replace it, but I cannot recognize which part of the car it is 🙂 It is somewhere near to gearbox? Under bonnet? In fuse box?
Sorry! I see now. I came here from google and didn’t realise I am looking on second subpage 🙂
Dear Sirs:
I have the same problem with my Mazda 6 AT 2.0 2015, this car use the same switch, or use another part number??
Looks like the 2015 uses the same part.