BULLETIN NOTE
This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red beside the change bars.
| Previously Issued TSBs: |
| 09-034/15 |
APPLICABLE MODEL(S)/VINS
2013-2016 CX-5 vehicles with VINs lower than JM3KE******663237 (produced before May 1, 2015)
2014-2016 Mazda6 vehicles with VINs lower than JM1GJ******430009 (produced before May 1, 2015)
DESCRIPTION
Some customers may complain that the front power (driver and/or passenger) seats do not slide back and forth properly or that they may be completely inoperative. This concern may be caused by a foreign object getting stuck under the power slide unit (below) while in operation. This can cause motor mounting bracket (A) deformation, resulting in motor cable (B) breakage.
| Power Slide Unit |
 |
To eliminate this concern, the shape of the motor mounting bracket (A) has been modified to increase its strength.
Customers having this concern should have their vehicle repaired using the following repair procedure.
REPAIR PROCEDURE
- Verify the customer concern.
- Inspect the motor cable (short one) and the motor mounting bracket:
- Is the motor cable broken?
- Is the motor mounting bracket deformed?
- If the results are ‘Yes” for either of the above inspections, replace the power slide unit with a newly established modified service part according to the replacement procedure.
NOTE: The seat illustrations shown throughout this bulletin are CX-5 (LH), unless noted otherwise.
- Remove the seat adjuster unit (A) according to MS3 Online or the workshop manual (section 09-13 FRONT SEAT ADJUSTER UNIT REMOVAL/INSTALLATION).
CAUTION: ALWAYS BE SURE TO USE THE PROPER TOOLS AND TECHNIQUES WHEN WORKING WITH FASTENERS, OTHERWISE, DAMAGE MAY OCCUR. SEAT FASTENERS ARE NOT SERVICED SEPARATELY AND ARE ONLY AVAILABLE WITH THE SEAT ADJUSTER UNIT.
Disassemble Seat Adjuster Unit:
- Remove four (4) bolts securing the four (4) links (A) to the sliders (B).
- Remove the front link (A) (inner and outer) from the slider (B) by gently bending the slider inward and the link outward.
CAUTION: Be careful not to damage the link bushing (A) during removal.
| After Link Removal |
 |
NOTE: CX-5 Only: Some vehicles of specific production dates use a plastic washer (A) between the slider and the link. Discard the plastic washer as it will not be reused.
- Remove the rear links (A) (inner and outer) from the sliders (B) by gently bending the slider outward and the link inward.
Assemble Seat Adjuster Unit Using a New Power Slide Unit:
- Install the rear links (A) (inner and outer) to the sliders (B).
| Rear-Inner | Rear-Outer |
 |
 |
CAUTION: DO NOT bend the slider too much. It could become deformed, causing improper operation.
CAUTION: DO NOT damage the bushing (A) in the slider during link installation.
- Install the front link (inner and outer) to the slider.
CAUTION: Pay close attention not to damage the bushing (A) during link installation.
- Using a suitable pry tool, install the link until it is properly seated.
- Tighten the four (4) link bolts as shown below.
Tightening Torque: 15.7-22.6 Nm {11.6-16.7 ft.-lbf., 1.6-2.3 kgf-m}
NOTE: Install the washer (A) for the rear link (B).
- Remove the position sensor (A) (if installed) from the old power slide unit, then reinstall it to the new power slide unit.
- Remove the screw (A) then push the clip (B) to remove the position sensor.
- Install the seat adjuster unit according to MS3 Online or the workshop manual (section 09-13 FRONT SEAT ADJUSTER UNIT REMOVAL/INSTALLATION).
- Verify the seat slides back and forth properly.
PART(S) INFORMATION
IMPORTANT: Confirm the part number of Seat Adjuster Unit (Original Part) for the subject VIN by checking the GEPC, then order the corresponding Power Slide Unit (New Service Part).
CX-5:
| Seat Adjuster Unit (Original Part) | Description | Qty. | Notes | Power Slide Unit (New Service Part) |
| KA0N-88-AF0 | Power Slide Unit (L), Fr. Seat | 1 | — | KAYN-88-AF0 |
| KA5P-88-AA0 | Power Slide Unit (R), Fr. Seat | 1 | — | KAYP-88-AA0 |
| KA0N-88-AA0 | Power Slide Unit (R), Fr. Seat | 1 | — | KAYN-88-AA0 |
| KD35-88-AF0A | Power Slide Unit (L), Fr. Seat | 1 | — | KDY6-88-AF0A |
| KD37-88-AF0A | Power Slide Unit (L), Fr. Seat | 1 | — | |
| KD51-88-AF0A | Power Slide Unit (L), Fr. Seat | 1 | — | KDY2-88-AF0A |
| KF69-88-AF0A | Power Slide Unit (L), Fr. Seat | 1 | — | |
| — | Clip (for side cover) | 2 | Replace Parts | KD45-88-585 |
Mazda6:
| Seat Adjuster Unit (Original Part) | Description | Qty. | Notes | Power Slide Unit (New Service Part) |
| GLK3-88-AF0 | Power Slide Unit (L), Fr. Seat | 1 | — | GLY3-88-AF0 |
| GJS2-88-AF0 | Power Slide Unit (L), Fr. Seat | 1 | — | GJY3-88-AF0 |
| GHL2-88-AF0 | Power Slide Unit (L), Fr. Seat | 1 | — | GHY2-88-AF0 |
| GLK4-88-AA0 | Power Slide Unit (R), Fr. Seat | 1 | — | GLY5-88-AA0 |
| GHL2-88-AA0 | Power Slide Unit (R), Fr. Seat | 1 | — | GHY2-88-AA0 |
| — | Clip (for side cover) | 2 | Replace Parts | KD45-88-585 |
WARRANTY INFORMATION
NOTE:
- This warranty information applies only to verified customer complaints on vehicles eligible for warranty repair.
- This repair will be covered under the New Vehicle Limited Warranty term. Additional diagnostic time cannot be claimed for this repair.
| Warranty Type | |
| Symptom Code | 64 |
| Damage Code | |
| Part Number Main Cause | (SEE PART(S) INFORMATION) |
| Quantity | 1 |
| Operation Number / Labor Hours | XXL53DRX / 0.8 Hrs. (Driver side only) XXL53ERX / 0.9 Hrs. (Passenger side only) XXL53FRX / 1.5 Hrs. (Both sides) |
NOTE. For the passenger seat, the following labors are included:
- DTC INSPECTION [TWO-STEP DEPLOYMENT CONTROL SYSTEM]
- OCCUPANT CLASSIFICATION SENSOR CALIBRATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM]
09-006/16
02/03/2016
SaleBestseller No. 1
FOXWELL Car Scanner NT604 Elite OBD2 Scanner ABS SRS Transmission
- [Easy to Use—Work Out of the Box] + [FOXWELL 2026 New Version] FOXWELL NT604 Elite scan tool is the 2026 new version from FOXWELL, designed for car owners who want to figure out the cause of issues before fixing car problems by scanning common systems like ABS, SRS, engine, and transmission. The NT604 Elite obd2 scanner diagnostic tool comes with the latest software—no need to waste time downloading software first. Plug the scanner into the OBDII port with OBDII cable to start the diagnosis.
- [Affordable] + [Reliable Car Health Monitor] Will you be confused what happens when the warning light of ABS/SRS/transmission/check engine flashes? Instead of taking your cars to dealership, this FOXWELL scanner will help you do a thorough scanning and detection for your cars and pinpoint the root cause. Note：The device is a diagnostic tool, not a repair tool. To turn off a warning light, you must first physically repair the issue causing it. Only then can the scanner be used to clear the corresponding fault code.
- [5 in 1 Car Diagnostic Scanner] Compared with obd scanners (50-100), NT604 Elite code scanner not only includes their OBDII diagnosis but also serves as ABS/SRS scanner, transmission and check engine code reader. When it’s an odb2 scanner, you can use it to check if your car is ready for annual test through I/M readiness menu. In addition, live data stream, built-in DTC library, data play back and print, all these features are a big plus for it. Note: doesn't support maintenance functions like reset or relearn. For the SRS system, NT604 Elite can read and clear common fault codes not caused by a crash, but crash/collision data cannot be cleared.
- [Fantastic AUTOVIN] + [No extra software fee] Through the AUTOVIN menu, this NT604 Elite car scanner allows you to get your V-IN and vehicle info rapidly, no need to take time to find your V-IN and input one by one. What's more, the NT604 Elite ABS SRS scanner supports 60+ car brands from worldwide (America/Asia/Europe). You don’t need to pay extra software fee. AUTOVIN may not work on some older vehicles or certain vehicle brands. If AUTOVIN fails, please input the vin code manually or go to the Diagnostic Menu to select your vehicle model.
- [Solid protective case KO plastic carrying bag] + [Lifetime update] Almost all same price-level car scanner diagnostic tool only offers plastic bag to hold the scanner.However, NT604 Elite automotive scanner is equipped with solid protective case, preventing your obd2 scanner from damage. Then you don’t need to pay extra money to buy a solid toolbox.
SaleBestseller No. 2
OBDMATE OBD2 Scanner with ABS SRS Transmission Diagnostic Tool
- 【Reset ABS/SRS/Transmission/Engine Lights】 More than an check engine code reader, OBDMATE OM901 obd2 scanner performs comprehensive diagnostics for the 4 most-used systems (ABS/SRS/Engine/Transmission). It quickly clears fault codes, turns off warning lights, read data stream and auto VIN.
- 【3.5" Handheld Scanner with 4 System Diagnose】 3.5" Super large TFT screen equipped displays an intuitive menu and clear readings of various sensors from ABS, SRS, ECM and TCM systems. It arrived with a silicone protective case and hard-shell carrying case, ensuring long-lived durability and drop resistance. The car diagnostic tool is plug-to-play designed, plug it and get diagnosis started without any batteries or updates required.
- 【One-Click I/M Readines&Full OBD2 Functions】 Press F1 to get an intuitive corloured form about whether various emissions-related systems on the vehicle are operating properly. Help you get smog-check ready quickly. OM901 car scanner supports all essential OBD2 functions you need: read & clear codes, view freeze frame, read I/M readiness, retrieve VIN, live data stream (with graphing display), O2 sensor test, onboard monitoring mode, and EVAP leak test.
- 【Battery Voltage Check&DLC Pin Test】 It allows you to monitor battery health by testing current battery voltage. Plus, this obd2 diagnostic tool features DLC 16-PIN test to check current voltage of every pin.
- 【Automotive Scanner Diagnostic Kit】 The package comes with 1 car scanner, 1 USB-type c cable, 1 hard storage bag and 1 user manual(en). Free to update without any hidden fees. 5 languanges available in setting including English, French, Italian, German and Espanish. Valuable and Portable, making it a great tool kit for car owners, DIY enthusiasts, and professional mechanics.
Bestseller No. 3
BlueDriver OBD2 Scanner Bluetooth, No Subscription, ABS SRS TPMS
- [Diagnose Like a Pro] BlueDriver Pro is a professional OBD2 scanner and diagnostic tool that helps you scan, understand, and clear vehicle trouble codes with confidence. Turn your phone into a powerful car diagnostic scanner—no guesswork, no unnecessary repairs.
- [Read and Clear More Codes Than Ever] Read and clear more codes than basic car code readers. Access enhanced diagnostics for Check Engine, ABS, SRS, Airbag, TPMS, Transmission.
- [Verified Fixes and Real-Time Data] Get unlimited, technician-verified repair reports matched to your VIN, with definitions, causes, and confirmed fixes. Monitor live vehicle data as you drive, view freeze frames, check smog readiness, and analyze Mode 6 test results.
- [Wireless & Bluetooth Enabled] - Say goodbye to wires. BlueDriver connects with Bluetooth via your phone/tablet to a sensor that plugs into your car's OBDII port. Get all of the capabilities of an expensive code reader & scan tool without any annoying wires.
- [Broad Make & Model Coverage] Strong support for GM, Ford, Stellantis (RAM, Jeep, Chrysler), Toyota, Honda, Nissan, Mazda, Subaru, Hyundai, Mercedes-Benz, BMW, and VW.
Bestseller No. 4
Outzone B800 BMW SRS Airbag Reset Tool | OBDII Scanner Read & Clear Fault Codes | Fits E36/E46/E34/E38/E39/Z3/X5 (1994-2003) – Except 2001 330i
- ✔️【Professional SRS Reset for 1994-2003 BMW】 Designed specifically for classic BMW models (1994-2003). This B800 scanner reads & clears SRS airbag fault codes, turns off the warning light, and saves you a costly dealer visit. Confirmed compatible with: E36, E46 (EXCEPT 2001 330i), E34, E38, E39, Z3, and X5 (E53). NOT compatible with any BMW built before 1994 or after 2003.
- ✔️【Important: Two Different Connection Ports – Read Before Use】 To avoid “not working” issues, please note: For 1994–2000 BMWs (most E36, E34, Z3, early E39), the SRS diagnostic port is a round 20-pin connector under the hood. You MUST use the included 16-pin to 20-pin adapter cable. For 2000–2003 models (late E46, E39, X5), use the standard OBD-II port inside the cabin. Incorrect connection is the #1 reason for “incompatibility” reports.
- ✔️【Read & Clear Fault Codes in Minutes】 Quickly diagnose why your SRS light is on. The scanner accurately reads fault codes from airbag and seatbelt pretensioner systems. With one button press, clear the codes and reset the SRS warning light in seconds. No expensive dealer tools needed.
- ✔️【User-Friendly for DIYers – No Mechanic Required】 Easy operation with an intuitive button layout: ‘Enter’ to confirm, ‘Scroll’ to navigate. The clear LCD screen shows results instantly. Includes a step-by-step manual (revised for clarity) to guide you through the entire reset process.
- ✔️【Reliable Support with 1-Year Warranty】 We stand behind the quality of our B800 scanner. It comes with a 1-Year Hassle-Free Warranty. If you have any questions or need support, please contact us with your Order ID, and our dedicated team will assist you promptly.
SaleBestseller No. 5
BLCKTEC 460T OBD2 Scanner Car Code Reader Engine ABS SRS Transmission Diagnostic Tool, 12 Reset Services, Oil/TPMS/EPB/BMS/SAS/DPF/Throttle Reset, ABS Bleeding, Battery Test, Auto VIN, Free Update
- [All System Diagnostics, Professional-Level Scanner] - BLCKTEC 460T is the ultimate OBD2 diagnostic tool for home mechanics and professionals. It supports all 10 OBD2 modes, reads and clears Engine/Transmission/ABS/SRS codes, performs All-System Diagnostics, offers workshop reset tools, and provides real-time live data. It helps you pinpoint issues, assess your car's condition, and prepare for SMOG checks with ease. NOTE: Function availability depends on your vehicle. Before you buy, be sure to use the Compatibility Checker on BLCKTEC website or contact our customer support to verify that the features you need are supported for your vehicle’s specific year, make, and model.
- [12+ Most Popular Reset Functions] - BLCKTEC 460T OBD2 scanner offers 12+ dealer-level service functions, including Oil Maintenance Reset, ABS Bleeding, EPB Reset, SAS(Steering Angle Sensor) Recalibration, DPF(Diesel Particulate Filter) Reset, Throttle Body Relearn, Battery Reset/Initialization, TPMS Relearn, Transmission Reset, Fluid Change Reset, Maintenance Reset and more, enabling you to perform workshop services like a pro. NOTE: Function availability depends on your vehicle. Be sure to use the Compatibility Checker on BLCKTEC website to verify that the features you need are supported for your vehicle.
- [Real-Time OBD2 and OEM Live Data, Freeze Frame Data] - BLCKTEC 460T helps diagnose vehicle issues when warning lights like Check Engine Light or ABS/SRS Light appear. It offers detailed DTC info, ECU Freeze Frame Data, and real-time OBD2 and advanced OEM live data, including Engine, Transmission, ABS, SRS, and more, making it easy to diagnose and resolve vehicle problems. You can view, graph, record, replay, and overlay up to four live data streams in a single graph for better analysis.
- [AutoVIN, AutoReLink, AutoScan, 3X Faster] - Equipped with AutoVIN technology, 460T automatically retrieves the VIN to save you time. Its AutoScan and AutoReLink features scan all of the vehicle's ECUs and detect any fault codes immediately after you plug the scanner into the vehicle's OBD2 port - no button presses required. Additionally, it regathers DTC and I/M readiness information every 30 seconds, simplifying monitor tests. 460T's advanced technology makes it 3X faster than other products.
- [Get RepairSolutions2, the #1 Auto Repair App for Free] - When paired with RepairSolutions2(RS2) App, 460T becomes even more powerful. RS2's Verified Fix Database built by master technicians, provides the parts needed for the repair. Additionally, RS2 gives you access to OEM warranty info, maintenance schedules, TSB, and dealership recall info, making car care easier than ever. RS2 is free with no subscription fees and it stores your car scan reports in the cloud, allowing you to access, share, or print them anytime and anywhere.
This product presentation was made with AAWP plugin.
Is there a way to get just the small cable that breaks without buying the whole slide motor assembly and if so what is the part number
I don’t think so.
No, it’s a rip off. I found a couple at a local junkyard for literally a couple bucks.