“This site contains affiliate links for which OEMDTC may be compensated” |
Subject:
ENGINE VIBRATION AND RATTLE NOISE AT IDLE (NO.3 ENGINE MOUNT) | Bulletin No: 01-012/16 |
Last Issued: 08/26/2016 |
BULLETIN NOTE
This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted below in Red beside the change bars.
Previously Issued TSBs | Date(s) Issued |
01-012/16 | 04/29/15 |
01-017/15 | 08/04/15 |
APPLICABLE MODEL(S)/VINS
2014-16 Mazda3 (Japan built 2.0L) with VINs lower than JM1BM******345755 (produced before April 6, 2016)
2014-16 Mazda3 (Mexico built 2.0L) with VINs lower than 3MZBM******310796 (produced before June 6, 2016)
DESCRIPTION
Some vehicles may exhibit an engine vibration and rattle noise at idle in D or R range after the engine reaches normal operating temperature. This may be caused by the orifice of the oil-filled No.3 engine mount becoming clogged with deposits generated inside, changing the damping characteristic of the engine mount. To correct the problem, the engine mount has been/will be modified.
Customers having this concern should have their vehicle repaired using the following repair procedure.
REPAIR PROCEDURE
- Verify customer complaint.
- Replace the No.3 engine mount with a newly established modified part used in mass production or a previously established modified service part according to the instructions on MS3 online (ENGINE MOUNT DISASSEMBLY/ASSEMBLY [SKYACTIV-G 2.0, SKYACTIV-G 2.5]).
- Verify repair.
PART(S) INFORMATION
NOTE:
- The modified No.3 engine mounts used in mass production are now available and can be used.
- The service parts and the parts used in mass production have the same performance.
- Check EPC for the part number of the original No. 3 engine mount equipped to the VIN and use the corresponding modified (new) No.3 engine mount.
Part Number | Description | Qty. | Notes |
GHY0-39-060 or GHS4-39-060A | No.3 Engine Mount | 1 | A/T (2.0L) |
GHY1-39-060 or GHR9-39-060A | No.3 Engine Mount | 1 | M/T (2.0L) |
WARRANTY INFORMATION
NOTE:
- This warranty information applies only to verified customer complaints on vehicles eligible for warranty repair.
- This repair will be covered under Mazda
’s Powertrain Warranty.
- Additional diagnostic time cannot be claimed for this repair.
Warranty Type | A |
Symptom Code | 83 |
Damage Code | 93 |
Part Number Main Cause | GHY0-39-060 (A/T) GHY1-39-060 (M/T) |
Qty. | 1 |
Operation Number / Labor Hours: | XXL5PXRX / 0.6 Hrs. |
01-012/16
- Mobil 1 advanced full-synthetic motor oil 5W-20 utilizes Mobil 1’s signature Triple Action Formula to deliver outstanding engine performance, protection, and cleanliness.
- Helps protect critical engine parts for up to 10,000 miles between oil changes,* controlling oxidation to prevent oil breakdown and maintaining excellent viscosity
- Meets ILSAC GF-6 standards to help provide low-speed pre-ignition (LSPI) and timing chain wear protection while keeping your engine clean and helping to improve your fuel economy
- Helps extend engine life by working to prevent damaging deposits and sludge buildup
- Provides excellent internal engine heat protection (up to 500 degrees F) and low temperature protection (to -30 degrees F)
- MaxLife Technology prevents engine breakdown with 40% better wear protection than the industry standard
- Includes seal conditioners to reduce oil consumption and oil leaks in high mileage engines.
- Added detergents reduce sludge, corrosion, rust and deposits to help keep motors clean inside and ensure a smooth-running engine.
- Advanced friction-fighting additives help maximize performance and improve fuel efficiency.
- Meets or exceeds all requirements of ILSAC GF-6A, API SP, API SN with SN Plus, API SN
- 6X better wear protection on critical engine parts than industry standards**
- 1.3X better sludge protection than industry standards*
- 3X Stronger against viscosity breakdown than leading full synthetic^
- Protection for 10,000 miles between oil changes
- Meets or exceeds the following specifications: API SP/SN PLUS/SN | ILSAC GF-6 | Meets Ford WSS-M2C945-B1 | Meets Ford WSS-M2C960-A1 |
- Full synthetic 5W-20 motor oil that is made with natural gas and designed to maximize engine protection
- Backed by a 15,000-mile protection guarantee* to protect your pursuit of every mile
- Provides better fuel economy (based on the latest industry standards)
- Keeps pistons cleaner than required by the toughest industry standard (based on Sequence IIIH results)
- Designed for high-performance engines
- Advanced protection against the four main causes of engine breakdown: wear friction heat and deposits
- 40% better wear protection vs. industry standards as tested in the Sequence IVB engine test
- 25% better deposit protection with superior engine cleaning detergents as tested in the GMOD engine test
- Full synthetic formula offers 24X stronger protection against engine-killing contaminants than the leading full synthetic motor oil
- Meets or exceeds all requirements of ILSAC GF-6A, API SP, API SN with SN Plus, API SN
- Full synthetic 5W-20 motor oil provides strong engine performance and protection against deposits between oil changes
- Ideal for use in modern turbocharged engines and high-performance vehicles like sports cars, SUVs, trucks, and minivans
- Designed to deliver more power and less friction, reducing friction to maximize horsepower (compared to Quaker State motor oil)
- Provides improved fuel economy (based on the latest industry standard)
- Excellent protection against formation of sludge and other harmful deposits (based on Sequence IIIH & VH tests on 0W-20 engine oil)
- Leading Manufacturer Of High-Quality Products
- International Renown For Our Diverse Range Of Award-Winning Products
- Fully Equipped With State-Of-The-Art Technology
- All Products Have Been Designed With The Professional In Mind
- Constantly Modernizing Our Powerful Devices To Meet The Demands Of The Modern User
- 3X Stronger than the leading full synthetic*
- 10X Better high stress performance**
- 20,000 miles between oil changes***
- Approved and Licensed Specifications: Exceeds API SP/SN PLUS/SN/SM |ILSAC GF-6 | Meets engine test requirements of Chrysler MS 6395 | Meets Ford WSS-M2C945-B1 | Meets Ford WSS-M2C960-A1 |
- Viscosity breakdown as measured in Kurt Orbahn test on 5W-30 grade |**As measured in Seq IX test under high load/torque conditions vs. API SP test limits | ***Or one year, whichever comes first
- Phosphorus Replacement Technology to help extend the life of the emission system
- Reduces leaks, oil burnoff and power robbing deposits
- 15,000 miles between oil changes*
- Meets or exceeds the following specifications: API SP/SN PLUS/SN/SM ILSAC GF-6 | Meets engine test requirements of Chrysler MS 6395 | Meets Ford WSS-M2C945-B1 | Meets Ford WSS-M2C960-A1
- Or one year, whichever comes first
- Premium-quality base oils and anti-wear additives that help extend engine life
- Superior protection against engine sludge
- Advanced protection against viscosity and thermal breakdown
- Superior protection against high-temperature deposits
- Meets or exceeds the following specifications: API SP/SN PLUS/SN/SM | ILSAC GF-6 | Meets Ford WSS-M2C945-B1 | Meets Ford WSS-M2C960-A1 |
Last update on 2025-04-17 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.