“This site contains affiliate links for which OEMDTC may be compensated” |
2013-2015 CX-5, 2014-2015 MAZDA6 – SEAT WARMER MALFUNCTION
APPLICABLE MODEL(S)/VINS
2013-2015 CX-5 vehicles equipped with seat warmers with VINs lower than JM3KE******531471 (produced before September 22, 2014)
2014-2015 Mazda6 vehicles equipped with seat warmers with VINs lower than JM1GJ******211892 (produced before September 29, 2014)
Inoperative seat warmer (or seat heater) on the driver and/or passenger seat.
When weight is applied to the seat, part of the heater element wire may come out of position and become bent.
Under repeated stress, the wire may break causing an inoperative seat warmer condition.
Repair Overview: | ||
Affected Seat | Repair | Notes |
Driver | Replace Seat Cushion Warmer | Do not replace seat cushion pad assembly. |
Passenger | Replace Seat Cushion Pad Assembly | Pad assy. includes improved seat warmer. |
REPAIR PROCEDURE
DRIVER SEAT:
- Verify the seat warmer in the driver seat is inoperative.
- Remove the seat cushion trim from the driver seat according to the MS3 online instructions or the Workshop Manual section 09-13.
- Proceed to “ Driver Seat: Seat Cushion Warmer Replacement Procedure” for seat warmer removal and installation of the modified seat warmer.
Driver Seat: Seat Cushion Warmer Replacement Procedure
Seat Warmer Removal:
- Identify the locations of double-sided adhesive tape, which secure the seat warmer to the seat cushion.
- Using a house-hold iron set to 140 ~ 150 degrees F (60 ~ 65.5 degrees C), carefully heat the pieces of double-sided adhesive tape (A) and gradually remove them all.
NOTE: DO NOT apply the iron directly to the cushion pad, as it could melt the pad.
- Remove the old seat warmer from the seat cushion, then proceed to “Seat Warmer Installation”.
Seat Warmer Installation:
- Peel off the protective film from the double-sided adhesive tape from the upper section of the new seat warmer.
NOTE: DO NOT remove the other pieces of protective film at this time.
- Align the bottom edge of the seat warmer (A) with the groove in the pad (B) as shown below. Press the seat warmer to affix it to the pad.
- Peel off the protective film from the double-sided adhesive tape from the middle section of the seat warmer.
- Press the two (2) seat warmer bridges (A) into the groove in the pad.
NOTE:
- DO NOT allow too much tension or too much slack in the seat warmer bridges (A).
- DO NOT place the seat warmer bridges (A) over the pad wires (B).
- Align the edge of the seat warmer (C) in parallel to the line of the pad groove. Press the seat warmer to affix it to the pad.
NOTE: Disregard the groove (A) in the pad shown below. It is not used during the repair.
- Affix the remaining (upper and lower) sections of the seat warmer to the seat cushion in the same manner as described above in Steps 3 ~ 5.
- Reinstall the driver seat cushion trim according to the MS3 online instructions or the Workshop Manual section 09-13.
- Verify proper seat warmer operation.
PASSENGER SEAT:
- Verify the seat warmer in the passenger seat is inoperative.
- Remove the seat cushion trim from the passenger seat according to the MS3 online instructions or the Workshop Manual section 09-13.
- Replace the seat cushion pad assembly with a modified part.
NOTE: The passenger side seat cushion pad assembly includes the improved seat warmer.
- Reinstall the passenger seat cushion trim according to the MS3 online instructions or the Workshop Manual section 09-13.
- Verify proper seat warmer operation.
PART(S) INFORMATION
CX-5 | |||
Part Number | Description | Qty. | Spec. |
KD49-88-123A | Seat Cushion Warmer (Drivers Seat) | 1 | Cloth (Type B Cushion Pad) |
KD51-88-123A | 1 | Leather (Type B Cushion Pad) | |
KD35-88-11XA | Seat Cushion Pad (Passenger Seat) | 1 | Leather |
KE40-88-11XA | 1 | Cloth (Type B Cushion Pad) |
Mazda6 | |||
Part Number | Description | Qty. | Spec. |
GHL2-88-123 | Seat Cushion Warmer (Driver Seat) | 1 | Leather Seat |
GHK3-88-123A | 1 | Cloth Seat | |
GLK3-88-11XA | Seat Cushion Warmer (Passenger Seat) | 1 | Leather Seat |
GJS1-88-11XA | 1 | Cloth Seat |